The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

Flowdur TF - Polyurethane Floor Coating

£72.00
(Inc. VAT)
£60.00
(Ex. VAT)
(No reviews yet) Write a Review
Weight:
3.20 KGS
Shipping:
Calculated at Checkout
Bulk Pricing:
Buy in bulk and save
Storage:
Store off the ground in un-opened packs in a dry store, under cover between 10ºC and 30ºC out of direct sunlight. Protect from frost. Prior to mixing, the temperature of the three components must be between 15 and 25 oC.
Pre Mixing:
Pre-mix the coloured resin component before use.
Mixing:
Add the full contents of the filler bag slowly & mix for a further 2 mins until a lump free consistency is obtained using a low speed electric mixer (300 rpm). When the aggregate is fully dispersed add the hardener component & mix until homogeneous
Application Conditions:
Ideal ambient and substrate temperature range is 15 - 25 ºC. Localised heating or cooling equipment may be required outside this range to achieve ideal temperature conditions. The substrate and uncured floor must be kept at least 3 ºC above the dew p
Application:
Apply using a medium nap roller direct from a paint tray/scuttle. Push the resin well into the surface, make sure it is fully wetted then pull back to a tight coat with the roller. Inconsistent application thickness will result in an uneven finish.
EU Directive 2004/42/EC:
Complies with category j type SB (< 500 g/l). The VOC content of Flowdur TF is approx. 24 g/l (theoretical).

Flowdur TF is a 3 pack, resin floor coating with a matt finish.  It is based upon polyurethane technology which provides excellent resistances to abrasion, chemical attack and other physical aggression.

It is a versitile product can also be used as a surface finish and sealer for Flowdur Wall Render and Flowdur Coving Mortar or as a top coat for Flowdur HF/RT/SL and MD floor toppings where refinishing is necessary. Flowdur TF may also be applied to grouted Flowdur SC and directly to prepared concrete in areas adjacent to other Flowdur floor toppings to maintain a degree of consistency of finish.

Suitable Surfaces: Concrete, Grano, Metals and Asphalts

Flowdur TF is ideal for use in areas requiring good wear and chemical resistance combined with economical cost with a matt finish.

Typical installations include:

  • Chemical storage areas
  • Warehousing
  • Laboratories
  • Food preparation areas
  • Communal areas and corridors

Appearance

Mottled matt finish. 

Thickness

Approximately 300 microns from two coats.

Chemical Resistance

Flowdur TF is resistant to a wide range of commonly used chemicals in the food, dairy and pharmaceutical industries such as concentrated citric acid (fruits), spirit vinegar (50% acetic acid), lactic acid (food & dairy products) and common alcohols (methanol & ethanol). Flowdur TF is also resistant to a wide range of inorganic acids, fuels, hydraulic oils, mineral oils and solvents. 

Good housekeeping practices should be employed at all times. Please consult our Technical Department for further advice. Some staining or discolouration may occur with some chemicals, depending on dwell time, temperature, type of chemical and degree of housekeeping employed. This does not affect the product’s service integrity or durability.

Surface Preparation

Surfaces to be treated must be sound free from oil or other contaminants, flaky paints, laitance and dust.  Smooth and dense surfaces must be mechanically abraded to provide a key and all dust

Usage: Indoor.  

Flowdur TF is not 100 % colour fast and may yellow over time. The rate of change will depend on UV light and heat levels and cannot be predicted. This will be more pronounced with lighter colours and blue shades and does not compromise the product’s performance or chemical resistance characteristics.

Coverage: A 3.2 kg unit will cover 8 sqm.

Coats Required: Two coats are usually required

Cure Schedule at 20 ºC

Working life of full packs * 15 minutes

* Usable working life of material following mixing and immediate spreading as per the application instructions. Decant mixed product into smaller quantities if applying to awkward areas as application time will be shorter if left in bulk.

Over-coat time: 12 - 48 hours

Cure time to light pedestrian traffic: 12 hours

Cure time to light wheeled traffic: 24 hours

Cure time to heavy duty traffic: 48 hours

Full chemical resistance - 7 days

Cleaning: Hot water and detergents.

Thickness: 0.3mm

Primer: Flowdur TF does not normally require the use of a primer. When treating extremely weak or porous concrete it is advisable to prime with Flowdur Primer. Please refer to technical data sheet. This primer should be allowed to cure for a minimum of 16 hours prior to application of Flowdur TF.

Typical Properties, 28 days at 20 ºC

BS 8204-6 FeRFA type 3

Abrasion resistance (EN 13892-4) AR 0.5

Abrasion resistance (BS 8204-2)   - Special Class Category A 

BRE Screed Test

Adhesion to concrete (BS EN 1504-2) > 1.5 MPa

Available Pack Sizes

3.2 kg and 8.25 kg units consisting of a resin, a hardener and a filler powder.

Technical Data

pdf-icon1.png