The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

Reecote EC017 Anti Static Gloss Floor Paint - 60 sqm

£432.00
(Inc. VAT)
£360.00
(Ex. VAT)
(No reviews yet) Write a Review
Weight:
32.00 KGS
Shipping:
Calculated at Checkout
Bulk Pricing:
Buy in bulk and save
Mixing:
The entire contents of the curing agent, component B, should be added to the entire contents of the resin pack, component A, and stirred thoroughly until uniform colour is achieved (2-3 minutes).
Application:
Apply the mixed material to the suitable prepared floor by brush or roller; ensure complete coverage of the floor area. Apply the second coat within 24 hours of the first. On very porous concrete a third coat may be required.
Coverage Guide:
Coverage 250g/m2. Single application Coverage is given as a guide only as the exact coverage will vary from floor to floor.
Curing Schedule:
At 20 degrees, pot life is 30 minutes. Waiting time between coats is 24 hours. Final drying times for light foot traffic is 1 day, lightly serviceable is 2 days and fully serviceable is 7 days,

Reecote EC017 AS is designed for use in areas where a build up of static may cause a problem for equipment or people. It is suitable for use where a hard wearing hygienic, anti static floor paint is required.

Suitable Surfaces: Concrete and steel

Advantages

  • Anti static epoxy floor coating
  • Low Odour
  • Hygienic and Easy Clean Finish
  • Good Chemical Resistance
  • Wide Colour Range
  • Can be made anti slip by using Virtus anti slip aggregate
  • Will not support bacterial growth.
  • Can be made decorative with the addition of Virtus PVA Flakes scattered into the wet resin, once dry, sand down any protruding or Flake edges and seal with Reecote ECO17 Anti-static Clear.

Usage

Indoor (some colour change would occur if used outdoors)

Resistant to: A wide range of acids and other chemicals.

Cleaning

Hot water jet washing with detergents and scrubber driers.

Thickness

Approx 0.5mm.  Can be built up to a mximum of 1 mm from the application of multiple coats.

Surface Preparation

Surfaces to be treated must be sound free from oil or other contaminants, flaky paints, laitance and dust. Smooth and dense surfaces must be mechanically abraded to provide a key and all dust.

New concrete should have an RH% of 75% or less. The substrate should be clean, free from laitance, oil, grease or other agents, which may impair adhesion. Cleaning techniques may include acid etching, grinding, light mechanical scabbling, blasting or degreasing, depending on wall contamination. Existing concrete walls should be sound and free from loose material. Damaged areas should be repaired with a Reepare Mortar prior to the coating application.

Mixing:

IT IS IMPERATIVE THAT THE MIXING IS CARRIED OUT IN THE RESIN CONTAINER. Reecote EC017 A/S is a two pack system and it is very important to ensure the curing agent, compound B, should be added to the entire contents of the resin pack, component A and stirred thoroughly until uniform colour is achieved (2-3 minutes). Packs should not be split unless accurate weighing facilities are available. Reecote EC017 A/S is supplied in pre-weighed units of the correct proportions.

Primer: 

Must be used with Reeprime CPS900.

Coverage: 

Each 5.772kg kit of Reeprime CPS900 will cover approximately 30 sqm.  Each 6kg of Reecote ECO17 AS will cover approximately 20 square metres.  Therefore this pack will cover approximately 60 sqm. 

Coats Required:

One coat of Reeprime CPS900 followed by two coats of Reecote ECO17 AS

Drying Time: 

Normally 16 hours at 20oc for foot traffic

Application

Reecote EC017 A/S should be applied to Reeprime CPS900 (see separate data sheet). Apply the mixed material to the suitably prepared floor by brush or roller; ensure complete coverage of the floor area. Apply the second coat within 24 hours of the first.

Pot Life: 30 Minutes (at 20oc)

Waiting time between coats: Min 12Hrs and Max 24Hrs (at 20oc)

Final Drying times:

Foot traffic - 1 day
Lightly serviceable - 2 days
Fully serviceable - 7 days

Pack Contents: 2 x Reeprime CPS900 Anti Static Primer and 3 x 6kg ECO17 AS.  This is enough to cover approximately 60 square metres of floor.

Colours 

  • Blue 18 C 35 (BS 4800)
  • Grey 7035 (RAL)
  • Blue 20 E 51 (BS 4603)
  • Black (no close RAL or BS match)
  • Grey 7031 (RAL)
  • Blue 18 E 53 (BS 4800)
  • White (no close RAL or BS match)
  • Grey 18 B 21
  • Green 6002 (RAL)
  • Red 3011 (RAL)
  • Grey 00 A 09 (BS 4800)
  • Green 14 E 53 (BS 4800)
  • Red 04 E 53 (BS 3800)
  • Grey 00 A 05 (BS 4800) range
  • Green 14 C 39 (BS 4800) range
  • Yellow 08 E 51 BS 4800 range
  • Beige 08 C 35 BS 4800 range