The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

Strongcoat LTC - Low Temperature Curing Epoxy Paint

£103.50
(Inc. VAT)
£86.25
(Ex. VAT)
(No reviews yet) Write a Review
Weight:
5.00 KGS
Shipping:
Calculated at Checkout
Bulk Pricing:
Buy in bulk and save

Strongcoat LTC may be applied at temperatures ranging from 25°C-5°C.

Cure times below 10°C will become extended but still show significant advantage over Standard or Fast Cure grades.

Strongcoat LTC is a two pack, solvent free, very hard wearing, epoxy floor paint for use in heavy duty areas where a hard wearing and chemical resistant surface is required.

Appearance

A smooth gloss finish in a range of attractive colours. Can have a textured finish with the addition of Anti-slip Aggregate.

Typical Installations

  • Processing and manufacturing plants.
  • Frequent fork lift truck traffic areas
  • Factories and warehousing
  • Food preparation, food storage areas and breweries.
  • Commercial garages, vehicle repair and maintenance depots, aircraft hangers
  • Chemical plant storage areas.
  • Car Parks

Advantages

  • Faster curing times
  • Can be applied in colder temperatures
  • Even on rough and uneven floors, it will cure to give a smooth, easy to clean surface.
  • Excellent chemical resistance.
  • Hygienic, seamless floor finish.
  • Low odour
  • Solvent free
  • Will not support bacterial growth.

Can be made decorative with the addition of Virtus PVA Flakes scattered into the wet resin, once dry, sand down any protruding or Flake edges and seal with Strongcoat Clear. Can be made anti-slip with the addition of Virtus Anti -Slip Aggregate scattered into the first coat of wet resin.

Suitable Surfaces

Concrete, metal, polymer modified cementitious screeds.

Low-temperature Cure

Similar to Fast Cure but even faster cure response with a further reduction in usable life which has a limiting effect over the volume which can be practically mixed and used at any one time. Resultantly smaller pack sizes are available in this grade.

Cured physical and chemical properties are little affected over those for the standard cure product.

Typical reductions in hard cure times are approximately 60% over that of the standard product but full cure and resistance to chemical attack will be in the order of 3-5 days compared to 5-7 for the standard cure systems.
 
Example:
 
Strongcoat Standard
Hard cure time @ 20°C  - 16 hrs
Usable life @ 20°C - 30-40 mins
 
Strongcoat LTC
Hard cure time @  - 20°C 6 hrs
Usable life @ 20°C - 15 mins
 
LTC grades may be applied at temperatures ranging from 25°C-5°C. Cure times below 10°C will become extended but still show significant advantage over Standard or Fast Cure grades.
 

Resistant to:

A wide range of acids and other chemicals.

Coverage: 

16-20 square metres per 5kg (2 coat application)

Coats Required: 

Two coats are usually required

Pack Sizes

5kg comprising of tin of resin and  tin of hardener.

Cleaning

Hot water jet washing, detergents and mechanical scrubber dryers.

Thickness

Approx 0.5 mm (from 2 coats).  Can be built up to a maximum of 1 mm thickness from the application of multiple coats.

Primer

A primer is not normally required.  However, on weak or porous concrete it is advisable to prime with Flowprime SF.  For floors suffering from oil contamination, where oil has penetrated the slab, it is available to prime with Flowprime OCS.   For floors where there is no damp proof membrane in the construction of the floor or if the concrete is new and has not had time to dry out thoroughly, it is advisable to use Flowprime DPM.

Surface Preparation

Surfaces to be treated must be clean, sound, free from oil or other contaminants, flaky paints, laitance and dust.  Smooth and dense surfaces must be mechanically abraded to provide a key.  Please read our Surface Preparation Datasheet.

Technical Data

Strongcoat (Standard) Technical Data Sheet

pdf-icon1.png

Strongcoat LTC Grade Information

pdf-icon1.png